On Fri, Apr 17, 2020 at 12:22:04PM +0800, Jason Wang wrote:
>
> On 2020/4/17 äå12:19, Jason Wang wrote:
> >
> > On 2020/4/15 äå12:20, Michael S. Tsirkin wrote:
> > > On Tue, Apr 14, 2020 at 01:12:51PM +0000, Vitaly Mireyno wrote:
> > > > > -----Original Message-----
> > > > > From:
> > > > > <> On Behalf
> > > > > Of Jason Wang
> > > > > Sent: Tuesday, 7 April, 2020 10:56
> > > > > To: ; Virtio-Dev
> > > > > <>
> > > > > Cc: Michael S. Tsirkin <>
> > > > > Subject: [Virtio-networking] Doorbell mapping of vDPA
> > > > >
> > > > > ----------------------------------------------------------------------
> > > > > Hi all:
> > > > >
> > > > > To get native performance of VF, we need to map doorbell to
> > > > > guest to avoid unnecessary vmexit. In
> > > > > order to do this, we will launch qemu with page-per-vq=on.
> > > > > This means the each doorbell register
> > > > > should be located at the beginning of 4K page and does not
> > > > > share the page with other registers. Then
> > > > > vDPA framework can safely map it into the guest physical
> > > > > address (GPA) range defined by qemu. It
> > > > > could be either
> > > > >
> > > > > 1) a single doorbell register that is used by all virtqueues
> > > > >
> > > > > or
> > > > >
> > > > > 2) several different per-vq doorbell registers
> > > > >
> > > > > If you decide to implement a virtio-pci register layout,
> > > > > need to make sure for notification structure
> > > > > (4.1.4.4 of virtio spec):
> > > > >
> > > > > For each virtqueue, the result
> > > > > ofcap.offset+queue_notify_off*notify_off_multiplier is PAGE_SIZE (e.g
> > > > > 4K) alignment, and the doorbeel does not share the page with
> > > > > other registers.
> > > > >
> > > > > And it would be better if queue_notify_off,
> > > > > notify_off_multiplier can be changed via firmware for
> > > > > extra flexibility.
> > > > >
> > > > In some cases, these conditions could not be met for a
> > > > virtio-net hardware device over PCI transport.
> > > > queue_notify and notify_off_multiplier could not always be fully
> > > > controlled by the firmware. There could be hardware limitations
> > > > on flexibility degree of these parameters.
> > > > Specifically, the limitations I'm thinking of are:
> > > > Â * queue_notify_off>0 and notify_off_multiplier>0
> > > > Â * Several doorbell registers of several virtqueues share the
> > > > same page (but don't share the page with other registers).
> > > >
> > > > Can this be supported in vDPA with direct doorbell mapping?
> > > >
> > > > Thanks
> > > There's value in being able to intercept some vqs in software
> > > while the rest of vqs are handled in hardware.
> > > E.g. that's the case for e.g. the control vq.
> >
> >
> > Good point, so in this case, the doorbell of control vq must exclusively
> > own a page.
>
>
> Or we need intercept the doorbells that share a page with control vq
> doorbell.
>
> Thanks
Which could be all of them. E.g. with a 4 byte offset, we are
talking 1K VQs per a 4k page.
>
> >
> > Or to facilitate the hardware design, we may introduce dedicated
> > notification area for control vq?
> >
> > Thanks
> >
> >
> > >
> > >
> > > > > Please check and make sure your hardware have such ability
> > > > > and feel free to ask if you have questions
> > > > > (offline if necessary).
> > > > >
> > > > > Thanks
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > _______________________________________________
> > > > > Virtio-networking mailing list
> > > > >
> > > > > https://urldefense.proofpoint.com/v2/url?u=https-3A__www.redhat.com_mailman_listinfo_virtio-
> > > > >
> > > > > 2Dnetworking&d=DwIGaQ&c=nKjWec2b6R0mOyPaz7xtfQ&r=lDHJ2FW52oJ3lqqsArgFRdcevq01tbLQAw
> > > > >
> > > > > 4A_NO7xgI&m=pddgVCz-
> > > > > orGTuUXATJ4Dmi7vAXatG9w47AmULNC3V9A&s=5mfYWbLCjcZO8FcwDqgAc5bjE-H-
> > > > > 4p5TBkRZqP3uMsQ&e=
> >
> >
> > ---------------------------------------------------------------------
> > To unsubscribe, e-mail:
> > For additional commands, e-mail:
> >
